Journal of Textile Science and Technology

Journal of Textile Science and Technology

Investigation of the effect of the composition ratio of chitosan nanofibrils/zinc oxide nanoparticles on the properties of the produced composite nanofibers

Document Type : Research/ Original/ Regular Article

Authors
Marziyeh Ranjbar-Mohammadi 1
Parinaz Shakoori 2
1 1. Textile group, Faculty of Engineering, University of Bonab, Postal Code 5551761167, Bonab, Iran
2 Textile group, Faculty of Engineering, University of Bonab, Postal Code 5551761167, Bonab, Iran
10.22034/jtst.2025.477859.1473
Abstract
Aim: This study investigated the potential application of a nanofibrous structure mimicking the natural extracellular matrix (ECM) of the body, composed of keratin/polyvinyl alcohol (K/PVA), polylactic acid (PLA), and chitosan nanofibrils/zinc oxide nanoparticles (ZnONPs/CHNF) (CSZ).

Methods: In this research, hybrid nanofibrous scaffolds were produced using K/PVA and PLA via the electrospinning method. K/PVA from one syringe and PLA from another were injected to produce hybrid nanofibers. Nanofibrillated chitosan/zinc oxide nanoparticles (ZnONPs/CHNF) (CSZ) at three different blend ratios (1:0, 2:1, and 1:2) were incorporated into the polymeric solutions containing K/PVA. The hydrophilicity of the samples was evaluated by measuring the contact angle, and the morphology of the produced scaffolds was examined using a scanning electron microscope (SEM). The effect of CSZ on morphology, hydrophilicity, and cell culture properties was then assessed.

Findings: The results demonstrated that the addition of ZnONPs to the CSZ solution led to a reduction in nanofiber diameter and an increase in the contact angle of the produced scaffolds. Extensive and suitable fibroblast cell growth was observed on the (2:1) PLA/CSZ-(2:1) K/PVA/CSZ sample. This sample, with a diameter of 352.50 ± 31 nm and a contact angle of 47 ± 3°, closely mimics the structure of the body's extracellular matrix (ECM). Its high surface-to-volume ratio enhances cell adhesion, proliferation, and growth, identifying it as the optimal sample.
Keywords
Keratin
Poly vinyl alcohole
Polylactic acid
Nanofibers
Nanofibrillated chitosan/ZnO nanoparticles

Subjects

  1. Li, S. and X.-H. Yang, Fabrication and characterization of electrospun wool keratin/poly (vinyl alcohol) blend nanofibers. Advances in materials science and engineering, 2014. 2014.
  2. Gao, Y., et al., Electrospun antibacterial nanofibers: Production, activity, and in vivo applications. Journal of Applied Polymer Science, 2014. 131(18).
  3. Wan, Z., et al., Controlled hydrophobic biosurface of bacterial cellulose nanofibers through self-assembly of natural zein protein. ACS Biomaterials Science & Engineering, 2017. 3(8): p. 1595-1604.
  4. Boakye, M.A., et al., Fabrication and characterization of electrospun PCL-MgO-keratin-based composite nanofibers for biomedical applications. Materials, 2015. 8(7): p. 4080-4095.
  5. Liu, Y., et al., Electrospun nanofibers as a wound dressing for treating diabetic foot ulcer. Asian Journal of Pharmaceutical Sciences, 2019. 14(2): p. 130-143.
  6. Xing, Z.-C., et al. Keratin nanofibers as a biomaterial. in Int Conf Nanotechnology and Biosensors, Singapore. 2011.
  7. He, M., et al., Fabrication and characterization of electrospun feather keratin/poly (vinyl alcohol) composite nanofibers. RSC advances, 2017. 7(16): p. 9854-9861.
  8. Edwards, A., et al., Poly (ε‐caprolactone)/keratin‐based composite nanofibers for biomedical applications. Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2015. 103(1): p. 21-30.
  9. Hashmi, M., S. Ullah, and I.S. Kim, Electrospun Momordica charantia incorporated polyvinyl alcohol (PVA) nanofibers for antibacterial applications. Materials Today Communications, 2020. 24: p. 101161.
  10. Adeli, H., M.T. Khorasani, and M. Parvazinia, Wound dressing based on electrospun PVA/chitosan/starch nanofibrous mats: Fabrication, antibacterial and cytocompatibility evaluation and in vitro healing assay. International journal of biological macromolecules, 2019. 122: p. 238-254.
  11. Ding, B., et al., Preparation and characterization of nanoscaled poly (vinyl alcohol) fibers via electrospinning. Fibers and Polymers, 2002. 3(2): p. 73-79.
  12. Esparza, Y., et al., Preparation and characterization of thermally crosslinked poly (vinyl alcohol)/feather keratin nanofiber scaffolds. Materials & Design, 2017. 133: p. 1-9.
  13. Râpă, M., et al., Development of Bionanocomposites Based on PLA, Collagen, and AgNPs and Characterization of Their Stability and In Vitro Biocompatibility. Applied Sciences, 2020. 10(7): p. 2265.
  14. Zakaria, Z., et al., Mechanical properties and morphological characterization of PLA/chitosan/epoxidized natural rubber composites. Advances in Materials Science and Engineering, 2013. 2013.
  15. Zahedi, P., et al., Preparation and performance evaluation of tetracycline hydrochloride loaded wound dressing mats based on electrospun nanofibrous poly (lactic acid)/poly (ϵ‐caprolactone) blends. Journal of Applied Polymer Science, 2012. 124(5): p. 4174-4183.
  16. Vakili, M., et al., Application of chitosan and its derivatives as adsorbents for dye removal from water and wastewater: A review. Carbohydrate polymers, 2014. 113: p. 115-130.
  17. Fadaie, M. and E. Mirzaei, Nanofibrillated chitosan/polycaprolactone bionanocomposite scaffold with improved tensile strength and cellular behavior. Nanomedicine Journal, 2018. 5(2): p. 77-89.
  18. Crini, G., Recent developments in polysaccharide-based materials used as adsorbents in wastewater treatment. Progress in polymer science, 2005. 30(1): p. 38-70.
  19. Shan, X., et al., Electrospinning of chitosan/poly (lactic acid) nanofibers: the favorable effect of nonionic surfactant. Journal of applied polymer science, 2014. 131(22).
  20. Majidi, H.J., et al., Investigating the best strategy to diminish the toxicity and enhance the antibacterial activity of graphene oxide by chitosan addition. Carbohydrate polymers, 2019. 225: p. 115220.
  21. Fadaie, M., et al., Incorporation of nanofibrillated chitosan into electrospun PCL nanofibers makes scaffolds with enhanced mechanical and biological properties. Carbohydrate polymers, 2018. 199: p. 628-640.
  22. Almasi, H., P. Jafarzadeh, and L. Mehryar, Fabrication of novel nanohybrids by impregnation of CuO nanoparticles into bacterial cellulose and chitosan nanofibers: Characterization, antimicrobial and release properties. Carbohydrate Polymers, 2018. 186: p. 273-281.
  23. Radwan-Pragłowska, J., et al., Hybrid Bilayer PLA/Chitosan Nanofibrous Scaffolds Doped with ZnO, Fe3O4, and Au Nanoparticles with Bioactive Properties for Skin Tissue Engineering. Polymers, 2020. 12(1): p. 159.
  24. Amjadi, S., et al., Preparation and characterization of gelatin-based nanocomposite containing chitosan nanofiber and ZnO nanoparticles. Carbohydrate polymers, 2019. 216: p. 376-384.
  25. Ranjbar-Mohammadi, M., et al., Fibrous Structures Fabricated from Poly (lactic acid) andNanofibrillated Chitosan/Zinc Oxide Nanoparticles. Iranian Journal of Polymer Science and Technology, 2021. 34(2): p. 174-191.
  26. Ranjbar-Mohammadi, M., P. Shakoori, and Z. Arab-Bafrani, Design and characterization of keratin/PVA-PLA nanofibers containing hybrids of nanofibrillated chitosan/ZnO nanoparticles. International Journal of Biological Macromolecules, 2021. 187: p. 554-565.
  27. Ranjbar-Mohammadi, M., et al., Designing hybrid nanofibers based on keratin-poly (vinyl alcohol) and poly (Ɛ-caprolactone) for application as wound dressing. Journal of Industrial Textiles, 2021: p. 1528083721988978.
  28. Lee, S.J., et al., Electrospun chitosan nanofibers with controlled levels of silver nanoparticles. Preparation, characterization and antibacterial activity. Carbohydrate polymers, 2014. 111: p. 530-537.
  29. Yu, W., et al., Influence of zinc oxide nanoparticles on the crystallization behavior of electrospun poly (3-hydroxybutyrate-co-3-hydroxyvalerate) nanofibers. Polymer, 2010. 51(11): p. 2403-2409.
  30. Leung, V. and F. Ko, Biomedical applications of nanofibers. Polymers for Advanced Technologies, 2011. 22(3): p. 350-365.
  31. Naderi, P., et al., Evaluation of the effects of keratin on physical, mechanical and biological properties of poly (3-hydroxybutyrate) electrospun scaffold: Potential application in bone tissue engineering. European Polymer Journal, 2020. 124: p. 109502.
  32. Koski, A., K. Yim, and S. Shivkumar, Effect of molecular weight on fibrous PVA produced by electrospinning. Materials Letters, 2004. 58(3-4): p. 493-497.
  33. Anitha, S., et al., Optical, bactericidal and water repellent properties of electrospun nano-composite membranes of cellulose acetate and ZnO. Carbohydrate polymers, 2012. 87(2): p. 1065-1072.
  34. Liu, Y., et al., Simultaneous Enhancement of Strength and Toughness of PLA Induced by Miscibility Variation with PVA. Polymers, 2018. 10(10): p. 1178.
  35. Bakhsheshi-Rad, H.R., et al., Improved bacteriostatic and anticorrosion effects of polycaprolactone/chitosan coated magnesium via incorporation of zinc oxide. Materials, 2021. 14(8): p. 1930.
  36. Moradi, S., et al., A novel composite nano-scaffold with potential usage as skin dermo-epidermal grafts for chronic wound treatment. Journal of Skin and Stem Cell, 2022. 9(4).

  • Receive Date 10 September 2024
  • Revise Date 08 January 2025
  • Accept Date 08 January 2025